Tektronix Applications Expert

I would assume there is a board problem, or loose cable or, the screen being blue then blank gives some indication the screen is working some.
Below is the link to the service manual on tek.com if you whish to do more trouble shooting on your own.
https://www.tek.com/en/oscilloscope/tds2000-digital-storage-oscilloscope-manual/tds2000c-and-tds1000c-edu-series
There is a troubleshooting section in the manual.

To set up a repair RMA (model and serial number)
call 1-800-833-9200 opt 2. Or 1- 800-438-8165
Or send an email to rmarequest@tektronix.com
Or https://www.tek.com/en/service-quote
Or https://www.tek.com/en/services/repair/mytek_rma_request

Thank you for you interest. Unfortunately, we do not offer schematics for the DPO7000 series as only modular repair is available and we do not go down to the component level. If you would like more information on the parts for this series, please check this link: https://www.tek.com/en/oscilloscope/dpo70000-mso70000-manual-6.

Helllo. I advise that you will likely need an amplifier since there aren't going to be any RF siggens that meet that high output power requirement.

Hello! Here is the latest AWG70k software:
https://www.tek.com/en/support/software/application/awg70000-series-software-v81

Next, install the radar plug-in: https://www.tek.com/en/support/software/application/radar-plugin-v40

Hello. Unfortunately, the RM2000B rack mount will not match the TBS2000B. TSB2XX2B 2 channel model uses rack mount RMB2020. TSB2XX4B 4 channel model uses rack mount RMB2040.

Hi,

Unfortunately this part is not available.

You asked if the FCA3000 is a good replacement for the Fluke PM6685. I compared the specifications of the PM6685 to the FCA3000. Most specifications (Range, frequency resolution, time resolution, voltage resolution, etc.) of the FCA3000/3100 units are better than the PM6685, so the FCA3000/3100 could be a great option.

However, the PM6685 does have a battery option for field use. The FCA3000/3100 do not have a battery option, and these units require a power source (outlet).

The FCA3000/3100 has a few different models. These have an varying input range of 300MHz to 20GHz. The different models and specification can be reviewed at the FCA3000/3100 product page. I have linked this below.
FCA3000/3100 product page: https://www.tek.com/en/products/frequency-counters/fca3000-3100#

Let me know if you have any questions about the FCA3000/31000. If you are interested in purchasing or receiving a quote for one of the frequency counters/analyzers, feel free to contact our sales team at 1 800 833 9200.

The TDS3000 is in Calibration/Best Effort Repair - The product has exited the Full Support time period but is still eligible for calibration services, with either moderate or limited repair capabilities.

The 3 Series MDO is the recommended replacement for the TDS3000 Series.

I see that you have a few questions about the MSO56B oscilloscope. They are addressed below: How does the Scope store the data?
• Application/User Data is stored directly on the Linux/Windows Solid State Drive that can be accessed (installed/removed) underneath the instrument.
How does it sanitize?
• The sanitization procedures for the MSO56B is pretty straight forward, and mainly involves removing the SSD device from the bottom of the instrument.
• The sanitization procedures for the MSO56B can be found in the Declassification and Security on page 6.
• 5 Series MSO B Declassification and Security Manual: https://www.tek.com/en/manual/oscilloscope/5-and-6b-series-mixed-signal-oscilloscopes-declassification-and-security-6-series-mso
Does the user have access of using the operating system.
• I am not quite sure what is meant by this question. The MSO56B can operate as a dedicated oscilloscope (closed-Linux OS) or as a Windows PC (open Windows) with access the scope’s HW.
• Page 48 of the Datasheet: https://www.tek.com/en/datasheet/5-series-b-mso-mixed-signal-oscilloscope-datasheet

Do you have any other questions about the instrument? I would be happy to assist you. And If you are interested in purchasing or receiving a quote for an MSO56B, feel free to contact our sales team at 1 800 833 9200.

The MDO4034B-3 was an MDO4kB with the 3GHz spectrum analyzer option. We dropped that naming convention when the "C" model came out, but the MDO4034C with 3 GHz spectrum analyzer would be very similar to the MDO4034B-3 that you have. Most differences between the "B" and "C" models is listed here: https://www.tek.com/en/support/faqs/what-are-primary-differences-between-dpo-mso4000b-mdo4000-mdo4000b-and-mdo4000c